Blog

Aug 18, 2023

How to change integrated handlebars on a road bike

Difficulty Hard Alex heads down to the Pinarello store in London to get his integrated bars and stem changed, showing you all the steps so you can complete the job too. Impressive sprinter - quite

Difficulty

Hard

Alex heads down to the Pinarello store in London to get his integrated bars and stem changed, showing you all the steps so you can complete the job too.

Impressive sprinter - quite possibly the fastest member of the GCN team

Pinarello is a bike manufacturer based in Treviso, Italy. It produces a range of high-end bikes for road, track, mountain and electric disciplines. The company takes pride in being the most decorated bike manufacturer in Tour de France history.

Zipp is a cycling component company owned by American manufacturer SRAM. Zipp specialises in carbon fibre wheels as well as producing a number of other components with the sole mission of making cyclists faster.

Many modern bikes such a Canyon's Aero bike range use integrated cables and hose routing that goes through the headset and fork. This has a wonderful aesthetic to it with clean lines uninterrupted by hoses, but that does make changing out a handlebar and stem a far more involved job than on a traditional bike.

As Alex Paton says in the video, "swapping out an integrated handlebar and stem with the hoses inside, is what I think is one of the most frustrating jobs on modern bikes!"

Yet, fear not! With the help of this guide, Alex and Tristan at the London Pinarello store, you can easily follow along and change a set of integrated handlebars yourself. Alex also has a new set of Shimano Dura Ace brakes fitted in the video, so if you're just looking for some pointers on how brake sets work on integrated bars, this is definitely something you'll want to watch.

How to Steps

Prepare your bike, ideally by using a bike stand

Remove mounts and loosen levers

Wheel and brake preparation

Disconnect hoses

Trim the hoses

Remove the old bars

Fit the new bars

Complete bar fitting

Refit levers

Refit Hoses

Bleed the brakes

Refit pads and wheels

Fit any accessory mounts

Centre the bars

Wrap the bars

Tools Needed

Step 1

Prepare your bike, ideally by using a bike stand

First things first, getting the bike in a position and state to start working on it is a must. Ideally, you want to place the bike in a work stand, clamping it around the seatpost with the bike set at a good height to work on the handlebars. Once that is all set, peel back the lever hoods and remove the bar tape from the handlebars. Depending on the condition of the tape and how easily it can be removed, it can be reused, or alternatively this is the perfect time to fit some fresh new tape.

Step 2

Remove mounts and loosen levers

At this point it is best to remove any mounts for lights or head units, keeping them safely to one side with any bolts that accompany them. Once the bars are clear of all accessory mounts, using a 5mm hex wrench, loosen off the clamp bolts on each of the levers.

Step 3

Wheel and brake preparation

As the integrated bars have internal hose routing, the brakes are going to need disconnecting so that they can be fed through the bars. In preparation for this, and the subsequent bleed that will need to take place, the front and rear wheels need to be removed along with the brake pads. Once the pads are removed, the pistons will need to be separated using a piston separator tool so that the brake bleeding block can fit in the calliper.

Top Tip

It is important when the brake pads are removed to keep them in a clean area away from any oil or contaminants that could cause issues with the pad material.

Step 4

Disconnect hoses

Before we can remove the old bar, we firstly need to disconnect the brake hoses at the levers. This is done with a 7mm spanner. As you loosen the bolt this will open the hydraulic system so, at this point, don’t be unnerved if a small amount of brake fluid starts to leak out.

Be careful to wipe up any fluid that does leak so that it does not cause any damage to any other parts of the bike. With both hoses disconnected, the levers can now be removed and put to one side.

Top Tip

Ensure that the lever is not depressed whilst the brakes are disconnected, as this will cause more fluid to leak.

Step 5

Trim the hoses

In order to feed the hoses through the bar, they will need to be trimmed down using a specific hydraulic hose cutting tool. This will then allow the flare nut and compression fitting to be removed.

Step 6

Remove the old bars

At this point the stem clamp bolts can be loosened. Now, the top cap preload bolt can be fully removed from the steerer. The handlebars can then be removed from the fork by carefully lifting them at the same time as guiding the brake hoses through the internal routing of the bar.

Top Tip

The handlebars do not need to be fully removed, instead they just need to be loosened until there is no tension on the bolt.

Step 7

Fit the new bars

This step will vary slightly depending on the bar manufacturer as some brands like this MOST bar featured have an access panel to aid the hose routing whereas some will not.

Before fitting the bars back on to the steerer, feed the brake hoses through the bars. A small pick or screwdriver can be used to help locate the hoses as they exit the bar at the lever end. Once the hoses are routed you can then fit the bars on the steerer, ensuring that any spacers have been refitted in the desired configuration.

Top Tip

Double check that you have fed the correct hose to the correct side of the bar so that the each brake is operated by your preferred lever.

Step 8

Complete bar fitting

Now that the bar is fitted, the top cap and top cap bolt can be refitted with a small film of grease on the threads. Once fitted, a small amount of preload can be set with the top cap bolt to take up and play in the headset - this is typically in the region of 2-4Nm and must be completed before tightening the stem clamp bolts.

Step 9

Refit levers

When refitting the levers it is important to get them feeling correct and, most importantly, equal. Some brands will have markings to make this part easier, however you typically want the levers to be parallel with the ground and with each other for a neutral feel.

Once you are happy with the position, torque the clamp bolts up to the recommended figure with a hex wrench. For Shimano this is 6-8Nm.

Step 10

Refit Hoses

Now that the bars and levers are all set, it is time to prepare the hoses to be refitted. As we trimmed the hoses and removed the flare nuts and compression fittings, we firstly need to ensure that the hoses are still long enough for the new bar (especially if a wider one has been fitted). Once happy with the length of the hoses, the flare nut needs to be fitted onto the hose while making sure the threaded section is pointing towards the lever, then fit a new compression fitting and finally a new barb. Now it is time to refit the hose to the lever. Using a 7mm hex wrench Shimano recommends a torque of 7-9Nm, but check with the specific model and manufacturer before tightening.

Top Tip

Using specific hydraulic hose tooling for this section will make it a lot easier and make it far less likely that anything gets damaged during the process.

Step 11

Bleed the brakes

Since the system has been disconnected, it is important to bleed the brakes to ensure that any air that may have got into the hose of the lever is purged out and replaced with brake fluid. We have done a complete guide on bleeding brakes that can be found here. Once the bleed is complete, wipe the bars and levers down with IPA or brake cleaner to remove any fluid.

Top Tip

Some brakes like Shimano use a mineral oil, whereas others use a DOT fluid, so check what system you are using before carrying out a bleed.

Step 12

Refit pads and wheels

Now that the system has been bled, it is time to fit the brake pads and wheels back onto the bike. After a brake bleed the brake pistons will take a few pumps to self adjust back to where they need to be. Once the feeling has come back in the lever, ensure the calipers are still aligned and are not rubbing.

Step 13

Fit any accessory mounts

Any of the mounts for lights, computers or cameras can now be refitted to the bars. Make sure they are torqued to the recommend limit.

Step 14

Centre the bars

Now that everything is fitted and set up to your liking, ensure that the bars are centred and in line with the front wheel. This is easier to do with your bike off the work stand as you can get a better eye on the alignment of the bars when the bike is on the ground. When you are happy, tighten the stem bolts to the manufacturer's recommended torque limit. Take turns to tighten each bolt a small amount, trying to do both bolts up in equal increments.

Step 15

Wrap the bars

With everything complete but the bar tape, take one last check of the lever position and make sure it is comfortable and equal on each side. Once the bars are wrapped it is very difficult to adjust the levers so ensuring it is correct now will save a lot of pain later. If you have not wrapped bar tape before, we have a dedicated guide to wrapping handlebars that covers everything you need to know.